What It Is

ISO 9001 documentation structure is outlined in the ISO 10013 Standard - Guidelines for Developing Quality Manuals. This standard recommends using a three-level structure. In practice, many companies use four-level documentation model that includes records. 4-level quality management system is shown below:

Quality Manual - level 1

Procedures - level 2

Instructions - level 3

Records - level 4

Actually, the documentation structure starts from the policy. The policy defines, among others, commitments with what standard a company intends to comply with. If you choose to use this approach, your quality management system will have five levels, similar to the structure below:

Quality Policy - level 1

Quality Manual - level 2

Procedures - level 3

Instructions - level 4

Records - level 5

Document titles for your ISO 9001 QMS

Companies use various approaches to titling their manuals, procedures, instructions, etc. For example, one of my customers titled their quality manual as “Quality Management System Quality Manual.” This very descriptive title does define the document, but does not appear to be efficient.

It is a very typical convention in the medical device manufacturing and other regulated industries to call the second-level documentation Standard Operating Procedures, known as SOPs. Unless one has a level called “Non-standard Operating Procedures,” I really do not see a practical or economical reason for long titles like these. As long as the short name conveys the idea and leads us to the right place, let’s use it. I will promote this optimization and reduction of waste approach throughout this publication. Let’s not make things more complicated than they practically need to be.

Numbering your documents

It is not a specific requirement of the ISO 9001 or any other standard to uniquely identify a part or a document. It is perhaps a common-sense measure and a worldwide practice in any documentation system, to give a document or a component a number and a title, and to identify its revision level. As documentation titles, document numbering is an area for creativity and an opportunity for optimization.

One of my clients runs a small company of some 120 employees. Their documentation control procedure prescribed two numeration systems that dependent on the type of a document. QMS documents had numbers like XX-XXX, and production parts required part number format as XXXXXXX-XXX. One of the drawings had a number 000048-002. Folks on the floor called it “four-eight.”

Do these long numbers identify documents? Yes, they do! Are they economical? No, they are not! My customer’s system above allowed seven digits and therefore could deal with ten million documents or part numbers. When I worked with this business, they used some 300 documents. If one plans to grow from 200 - 300 documents to a million, one has a long way to go! It is not only how many documents your QMS uses, reading these long strings with five sequential zeros gave everybody headache. Even though this example looks too complicated, “The Worst Part Number” Grand Prize won my other client. They used 14-digit alphanumeric part numbers!

I hope it is clear that only when extensive part numbers are justified, we do not have other options. If you build helicopters or satellites, you, no doubt, will need millions of parts and therefore will need long part numbers. If not, make your life easy and stay away from all those zeros. The most practical system I worked with used a three-digit format for their part numbers. 202, 203, 204, and so on. Worked just fine!

There is another opportunity for improvement of many QMS - part number designation. Many companies relate a document number to a document type. For example, 20-xxxx indicates a procedure, 30-xxxx indicates a drawing, SOP-xxxx indicates a standard operating procedure, etc. My practice with a few QMS that used designation approaches showed that “no designation” systems are more practical. Several QMS that used designation I have worked with have failed. Not long ago, one of my clients mentioned that they ran out of range in their document numbering format. The QMS initially permitted for identifying suppliers through a two-digit identifier within the part number. While the company grew, the number of supplier increased beyond expectations and eventually the company needed more than 99 suppliers. This resulted in the document number format to being able to support new needs.

To get around this issue, there is a simple solution - a “no designation” system. Part or document numbers in such systems are assigned sequential unique numbers. Areas of use, materials, suppliers, and other attributes are not reflected in part numbers. Moving in this direction, you can simplify your system even more. I worked with a company that did not use document No. at all. That documentation system used just document name followed by a revision number, like Process Validation Protocol AB.